| ID | | Article Title | Post Date |
|
91 | 
| Installation of the Sonnet (ATTO OEM) RAID card in an 8-core Mac Pro with a Fusion D800RAID, R800RAID, or D400RAID storage system. | May-12-09 |
| Originally, the Sonnet (ATTO OEM) RAID card in an 8-core Mac Pro should be installed in the PCIe compatibility slot, not a PCIe 2.0 slot. If the RAID card must be inserted in a PCIe 2.0 slot, please do the following:
1) Upon rebooting your machine, launch the ATTO Configuration Utility.
2) Select the CLI tab and type "automap" to mount the drive array.
Note: A recent firmware was posted to the Sonnet website to address this issue. |
| |
|
98 | 
| ATTO R380 RAID Software (Feb. 2008) | Aug-05-09 |
|
101 |
| Fusion storage system activity lights are always on with Seagate ES.2 (Enterprise) drives installed in the drive bays. | Oct-22-10 |
|
202 |
| Under Mac OS X 10.5.6, the PCI Express Expansion Slot Utility (early Mac Pro) always reports 8x, 1x, 1x, 16x no matter how its set. | May-06-09 |
|
301 |
| Formatting a drive array greater than 16TB with APT (Apple Partition Table) fails in a Macintosh. | Jun-16-09 |
|
387 |
| How do I replace a failed drive under warranty if I'm in a sensitive/classified environment and can't send the old one back? | Mar-23-10 |
| Seagate has a provisions in place to deal with replacing drives in sensitive / classified environments.
1. Start by going to the Seagate Warranty Validation page http://support.seagate.com/customer/warranty_validation.jsp
2. Input all the neccessary drive information and continue until you are issued an RMA or return#.
3. Contact Seagate at http://www.seagate.com/www/en-us/about/contact_us to request a "Certificate Of Destruction". Seagate will send the COD via e-mail along with instructions on how to destroy the drive to their satisfaction. Certain parts of the drive will need to be shipped back to Seagate along with a filled out copy of the COD.
4. Once Seagate receives the COD and associated drive parts meeting their requirements, a replacement drive(s) will be shipped to the address set forth in the RMA. |
| |
|
445 |
| What is the default drive timeout in Fusion RAID systems? Should I change it? | Mar-24-10 |
|
450 |
| My storage shows 10% more capacity under OS X 10.6 than under OS X 10.5. Why? | Mar-24-10 |
|
775 |
| Does the ATTO R380 Support OS X 10.9 (Mavericks)? | Oct-21-13 |
|
788 |
| Can I use an ATTO R680 with the R800RAID or D800RAID? | Jun-24-14 |
|
955 |
| Can I use Seagate Iron Wolf drives; or Hitchai and WD drives 8TB and larger? | May-31-18 |
| Some newer drives use a hole pattern different from the traditional drive hole pattern for the bottom mounting points. The location of the bottom holes close to the connector did not change; however, the bottom holes near the middle have been removed and replaced with bottom holes close to the front of the drive.
The drives with the new bottom hole pattern include:
Seagate Iron Wolf drives (also missing the middle hole from the side mount hole troika)
Hitachi drives 8TB and larger
WD drives 8TB and larger
Incompatible mount holes
Echo 15+ Dock (side mount, but needs middle hole, so incompatible with only Seagate Iron Wolf)
Fusion F3 (bottom mount)
Fusion D400Q/R400P/D500P (bottom mount)
Fusion D800/R800 (bottom mount)
Compatible mount holes
Fusion R400S RAID (side mount)
Fusion R400 RAID USB 3 (side mount)
Fusion DX800/RX1600 (side mount) If using Iron Wolf line, must use Iron Wolf Pro with rotational vibration sensors
|
| |
| |
