| ID | | Article Title | Post Date |
|
27 | 
| How can I distinguish between the earlier Tempo-X eSATA (4+4 and 8e) products supporting 3 Gigabit/sec speeds and the older cards that support 1.5 Gigabit/sec speeds? | May-07-09 |
|
36 |
| What are the benefits of supporting Spread Spectrum Clocking (SSC)? | Mar-02-10 |
|
37 |
| Is it possible to boot from a volume that resides on the Tempo SATA card? | Mar-02-10 |
|
39 |
| Can I hot-swap a disk drive that is attached to any Sonnet Tempo Serial ATA card? | Mar-23-10 |
|
42 |
| Can the Tempo SATA cards co-exist with other manufacturers' Serial ATA cards? | Oct-27-09 |
|
44 |
| How can I distinguish between the earlier Tempo-X eSATA products supporting 3 Gigabit speeds and the older cards that supported 1.5 Gb speeds? | May-07-09 |
|
63 |
| Can I operate two Tempo SATA cards in the same system? | Sep-02-09 |
|
67 |
| What kind of performance can I expect from a using a Sonnet Tempo SATA Card in a PCI slot (like in a Power Mac G4)? | Oct-12-09 |
|
174 |
| Drive(s) connected to the Tempo-X SATA 4+4 occasionally do not appear when the computer is booted or an error message regarding the RAID array connected to the Tempo-X SATA 4+4 is occasionally displayed at boot up, and the RAID array cannot be used. | May-07-09 |
|
219 | 
| With a Tempo-X SATA host controller installed and drives connected, the computer locks up and will not respond to keyboard or mouse input, and must be forced to power off (press and hold the power button for more than 5 seconds) then restarted. | May-07-09 |
| This condition occurs when the System Preferences Energy Saver Put the hard disk(s) to sleep when possible checkbox is checked (on), or the Disk Sleep Timer is enabled; the Tempo-X SATA card using firmware version 1.2 does not support disk sleep.
To correct this issue, update the Tempo-X card's firmware to version 2.0 or later. Download and run the installer to add disk sleep support. |
| |
|
220 |
| Multiple Hitachi hard drives connected to a Tempo-X SATA host controller are not always detected (won't mount). | May-07-09 |
|
404 |
| The Sonnet Tempo SATA card does not work with my Western Digital My Book Premium ES Edition, or Seagate Technology FreeAgent Pro. | Mar-02-10 |
| Sonnet Tempo cards are compatible with most external SATA storage. However, external hard drives with USB 2.0/eSATA dual interface based on the Oxford Semiconductor OXU931DS storage controller chip may not be compatible with Mac OS X when connected via SATA. Known issues are kernel panics occurring when the drive is connected, or the drive not being recognized by the operating system.
Summary of eSATA storage
- Storage with eSATA alone.......................................................compatible
- Storage with Triple interfaces.................................................compatible
- Storage with Quad interfaces..................................................compatible
- Storage with eSATA plus Firewire 400 and/or 800..................compatible
- Storage with port multiplier support (multiple drives).............compatible
- Storage with RAID 0, 1, or 5 (multiple drives)..........................compatible
- Storage with eSATA plus USB (based on JMicron 20366)..........compatible
these compatible drives include, but are not limited to:
1) OWC Mercury On-the-Go USB 2.0/eSATA 2.5" portable
- Storage with eSATA plus USB (based on Oxford OXU931DS)....not compatible
these incompatible drives include, but are not limited to:
1) Western Digital My Book Premium ES Edition
2) Seagate Technology FreeAgent Pro |
| |
|
452 |
| I upgraded my Tempo SATA software in a PowerMac G4 or G5 and the card is giving a lot of system errors. | Oct-12-09 |
| This does not happen often, but sometimes the driver caches do not get purged and the new SATA driver does not get loaded correctly from ROM.
Try this:
1) Delete and empty trash for the following file and two directories:
/System/Library/Extensions.mkext (a file)
/System/Library/Caches/com.apple.kernelcaches (a directory)
/System/Library/Caches/com.apple.romextensions (a directory)
2) Restart |
| |
|
454 |
| I have connected a large hardware RAID volume (for example, a 4TB Fusion D400QR5) to a Sonnet Pro SATA card in a Macintosh, and it is showing up as only 2TB. Why? | Oct-14-09 |
|
459 |
| The performance of my drive array is significantly less than I expect. | Jun-14-11 |
|
544 |
| How do I uninstall the Sonnet Pro SATA Driver? | Dec-26-10 |
| |
