| ID | | Article Title | Post Date |
|
808 | 
| What 10GBase-T switches and PCIe cards has Sonnet tested for interoperability? | Dec-22-19 |
|
809 |
| What reasonably-priced 10GBASE-T switches can Sonnet recommend? | Dec-22-19 |
|
814 | 
| I'm getting low throughput on macOS. How can I fix this? | May-26-22 |
| You may need to set a few parameters to enable higher performance at 10Gb/s.
1) Set the mode to full-duplex, which allows the adapter to send and receive at the same time.
To set full-duplex on macOS, go into the System Preferences->Network and select the Twin10G interfaces. Click the "Advanced..." button in the lower right. In the Advanced window select the "Hardware" tab and set "Configure:" to "Manually". Set duplex to "full-duplex".
2) If your entire network will support it, set packet size to jumbo frames which pack six times as many bytes per packet.
For a large frame to be transmitted intact from end to end, every component on the path must support that frame size. The switches, routers, and NICs from one end to the other must all support the same size of jumbo frame transmission for a successful jumbo frame communication session. Switches that don't support jumbo frames will drop jumbo frames. In the event that both ends agree to jumbo frame transmission, there still needs to be end-to-end support for jumbo frames, meaning all the switches and routers must be jumbo frame enabled. At Layer 2, not all gigabit switches support jumbo frames. Those that do will forward the jumbo frames. Those that don't will drop the frames. For a jumbo packet to pass through a router, both the ingress and egress interfaces must support the larger packet size. Otherwise, the packets will be dropped or fragmented. If the size of the data payload can't be negotiated (this is known as PMTUD, packet MTU discovery) due to firewalls, the data will be dropped with no warning, or "blackholed". And if the MTU isn't supported, the data will have to be fragmented to a supported size and retransmitted, reducing throughput.
To set Jumbo frames on macOS, go into the System Preferences->Network and select the Twin10G interfaces. Click the "Advanced..." button in the lower right. In the Advanced window select the "Hardware" tab and set "Configure:" to "Manually". Set MTU to "Custom" and enter "9000".
3) Not all devices support flow control, or the absence of flow control. If Flow Control is off, turn it on; if it is on, turn it off.
4) Update your macOS to at least 10.13.6. Earlier versions enable SMB signing by default, which can cripple 10Gb networks. Update your macOS, or disable SMB signing. (You can Google how to do this.)
5) If you're in a macOS server environment:
If your Server is running 10.13.6+ enable SMB protocol, and disable AFP protocol.
If your Server is running 10.12.6- enable AFP protocol, and disable SMB protocol.
If your Server is running 10.13.6+, update your clients to 10.13.6+ for a significant performance boost. |
| |
|
972 |
| After I upgraded macOS, the Twin10G, Presto 10GbE, or other Sonnet PCIe card that requires a driver is not loading. | Dec-22-19 |
| If you have already installed a Sonnet Driver and it is not loading:
1) Restart (forces Mac OS to scan for unloaded drivers).
2) Go to System Preferences...Security & Privacy panel...General tab. You will see a message, "System software from developer "Sonnet Technologies" was blocked from loading." Click Allow. Note that you must have a hard-wired mouse/trackpad to click allow. If you are connecting via Remote Access, then macOS prevents you from clicking Allow.
3) Restart. |
| |
|
974 |
| Can I get increased performance from Link Aggregation in macOS? | Dec-22-19 |
|
993 |
| My system crashes, freezes, or fails to connect when I talk to a storage device on the network | May-13-22 |
|
994 |
| My Twin10G or Presto 10GbE is not working on macOS. | Dec-22-19 |
|
1053 |
| Microsoft Ending Support for Windows 7 | Apr-04-19 |
| Original release date: March 19, 2019
All software products have a life-cycle. After January 14, 2020, Microsoft will no longer provide security updates or support for PCs running the Windows 7 operating system. After this date, this product will no longer receive free:
• Technical support for any issues
• Software updates
• Security updates or fixes
Computers running the Windows 7 operating system will continue to work even after support ends. However, using unsupported software may increase the risks from viruses and other security threats.
The Cybersecurity and Infrastructure Security Agency (CISA) encourages users and administrators to upgrade to a currently supported operating system. For more information, see the Microsoft End of Support FAQ.
|
| |
|
1065 |
| I'm getting very slow performance with my Presto 10G PCIe card or Twin10G Thunderbolt 10G adapter with OS X 10.11-10.12. | Dec-22-19 |
|
1067 |
| How and when to use two Ethernet ports on a Mac | May-16-22 |
|
1152 |
| Does the Twin10G Thunderbolt Adapters or Presto 10GbE PCIe cards support NIC Teaming under Windows? | May-28-21 |
| |
