| ID | | Article Title | Post Date |
|
69 | 
| What are the known incompatibilities with the Crescendo/7200 v1.1? | May-12-09 |
|
71 |
| What type of RAM can I add to my Crescendo/7200 card? | May-12-09 |
|
85 |
| System will not boot, or consistently crashes early in start-up. | Jan-28-10 |
|
171 |
| The speed indicated on the G3 or G4 chip on my Sonnet processor upgrade doesn't seem to match the speed of the upgrade I purchased. What's the story? | May-07-09 |
|
177 |
| System will not boot, or consistently crashes early in start-up with a Crescendo/7200 upgrade card installed in computer. | May-07-09 |
|
218 |
| The computer's standard startup process takes noticeably longer after upgrading to any Mac OS 9.x system from Mac OS 8.6 or earlier. | May-12-09 |
|
221 | 
| After installing the Sonnet Crescendo/7200 into a machine with two other PCI cards, or adding an additional PCI card to a machine already running the 7200 upgrade, the computer does not boot past the "Happy Mac" icon. If I remove either one of the PCI cards or the upgrade, the computer will boot without a problem. The same is true if I boot up holding down the SHIFT key to boot with extensions off. | May-07-09 |
| In previous versions of the Crescendo/7200 enabler software, Sonnet was required to create specific "patches" for each PCI card supported. Whenever the firmware of a PCI card was updated, the 7200 enabler software required a version revision as well.
To address compatibility issues, upgrade the version of the 7200 enabler you are running on the machine to version 1.1 (or later) of the enabler software. In this new version an entirely new algorithm has been developed for recognizing PCI cards from the processor running on the PCI bus. This new breakthrough vastly expands compatibility to virtually all PCI cards. Also with the 1.1 release, PCI cards can be used in almost any combination, and utilize any and all available slots. It is still recommended that the Crescendo/7200 card occupy slot 1.
To update to version 1.1, remove the 7200 upgrade processor and boot the computer. Then download the Crescendo/7200 software. Once downloaded, run through the installation. The installer will remove any old version of the enabler that is currently installed and install version 1.1. When the installer is done, shut the computer down, reinsert the 7200 upgrade processor, and boot the computer normally. |
| |
|
222 |
| After installing the Sonnet Crescendo/7200 into my machine, making sure I followed the instructions on RAM distribution, the computer does not boot past the "Happy Mac" icon. If I remove the 7200 upgrade, the computer will boot without a problem. The same is true if I boot up holding down the SHIFT key to boot with extensions off. | Aug-06-09 |
|
223 |
| After installing the Sonnet Crescendo/7200 into a machine with 128MB RAM DIMMs, or adding 128MB RAM DIMMs to the machine that already was running the 7200 upgrade, the computer does not boot past the "Happy Mac" icon. The DIMMs work when installed alone on the logic board without the 7200 upgrade installed. If I remove either the 128MB RAM DIMMs or the processor upgrade, the computer will boot without a problem. The same is true if I boot up holding down the SHIFT key to boot with extensions off. | May-07-09 |
| Issue 1: 128MB DIMMs are typically composed of 16 chips, each a 16Mx4 part. There are two types that are used, the "4K Refresh" and the "8K Refresh". The Crescendo/7200 is not compatible with some DIMMs made with "8K Refresh" parts because the timing margins are so thin that the electrical \u8218\u196\u250 noise\u8218\u196\u249 generated by the card causes errors. The "8K" versus "4K" parts can be identified by the part numbers of the chips on the DIMM, or by checking with the manufacturer of the chips.
One solutions is to contact the chip vendor/manufacturer and have the chips replaced with DIMMs that are built with "4K Refresh" parts. 4K Refresh DIMMs are considerably more prevalent, but users are advised to ask before purchasing.
Issue 2: The 128MB DIMMs do meet compatibility, however, you are running an older version of the 7200 enabler.
After checking and verifying that the 128MB DIMMs that are installed on either the logic board or the card are made with "4K Refresh" parts and not "8K Refresh", check to see which version of the 7200 enabler you are running. This can be found in the System folder of your Operating System hard drive. If you are not running version 1.1 or later, you will need to update. With the release of the 7200 enabler, Sonnet expands its support of RAM running on both the upgrade card and the logic board. To update to version 1.1, remove the 7200 processor upgrade and boot the computer. Then download the Crescendo/7200 software. Once downloaded, run through the installation. The installer will remove any old version of the enabler that is currently installed and install version 1.1. When the installer is done, shut the computer down, reinsert the 7200 upgrade processor, and boot the computer normally. |
| |
| |
