| ID | | Article Title | Post Date |
|
72 | 
| The Crescendo/Encore installer hangs, or crashes the system; occurs most often when run from the Sonnet installer CD. | May-12-09 |
|
76 |
| Which current Encore/ST G4 processor upgrades include a pre-attached heat sink? | May-12-09 |
|
77 |
| I purchased an Encore/ST G4 processor upgrade that is just a card; is it less reliable than one with a pre-attached heat sink? | May-12-09 |
|
169 | 
| May I discard my original CPU after installing Sonnet's upgrade cards?
| May-07-09 |
| Sonnet recommends that you keep the original processor card even after installing our upgrade cards in case you ever need them. |
| |
|
171 |
| The speed indicated on the G3 or G4 chip on my Sonnet processor upgrade doesn't seem to match the speed of the upgrade I purchased. What's the story? | May-07-09 |
|
175 |
| The Crescendo/Encore installer hangs, or crashes the system; occurs most often when run from the Sonnet installer CD while using Mac OS 9. | May-07-09 |
|
176 |
| Sonnet OS X Installer Instructions | May-07-09 |
| MAC OS X USERS -- Install Sonnet Firmware Patch
This section describes the installation of software required to support the Encore ZIF, Encore ST, or ST Duet G4 in your computer. Please note you MUST run the Sonnet Firmware Updater before you install this upgrade card. If you do not run the updater, your computer will not operate with the processor upgrade installed.
1) Insert the Sonnet Installer CD into the CD-ROM drive. Double-click the Sonnet Install CD icon. When the Sonnet Install CD window appears, double-click the Mac OS X ONLY folder.
2) Double-click the Sonnet Firmware Updater icon; Mac OS X's built-in Install program will launch. Follow the onscreen directions to complete the installation of the Sonnet Firmware Updater and Sonnet Firmware Remover applications to your Applications folder.
3) Shut down your computer.
4) Press and hold the programmer's button until you hear a long tone; release the button when you hear the tone. Note: programmer's button is the little tiny pinhole on the front of a Quicksilver.
4a. For QuickSilver 2002: While holding the programmer's button, press and hold the 'start-up' button on the front of the Mac. When the Mac starts up, release the start-up button. Continue to hold the programmer's button and when you hear a long tone, release it.
5) Once the startup process is complete and you have logged in (if necessary), go to the Finder and select Applications from the Go menu.
6) Locate Sonnet Firmware Updater, and then double-click its icon to launch the application.
7) When the Sonnet Firmware Updater window appears, click OK.
8) When the Authenticate window appears, enter the Administrator password, and then click OK.
9) When the Wait message appears, DO NOT CLICK OK; just wait. Clicking the OK button will cause the application to quit. After the Wait message disappears, another message will appear indicating that the ROM is being patched. Do not turn the power off; this process may take several minutes.
10) When the message stating that the ROM has been patched appears, click OK. Shut down your computer; you may now install the Encore ZIF, Encore ST or ST Duet processor upgrade card.
Note: After updating your system's firmware with the Sonnet firmware installer, you do not need to install the other software located in the Mac OS X ONLY folder on the Sonnet Installer CD; that software is used for other processor upgrade cards by Sonnet. |
| |
|
204 |
| Mac OS 10.5 "Leopard" shuts down a few seconds into booting after a new installation of the OS. | May-07-09 |
| This problem has nothing to do with our processor upgrade being in the machine or with the firmware update that was done beforehand.
It has everything to do with how 10.5 was installed. Doing the 10.5 install as a simple "Upgrade" rather than using some of the other options like Archive and Install or Erase and Install.
When you do a straight upgrade, the installer just overwrites the old 10.4 System folder and that can leave some incompatible kernel extensions lurking in the new 10.5 folder whose response to that is to shut down on boot if it encounters something it doesn't like. So you need to do an Archive and Install of 10.5. This will create a new System folder, migrate your various user settings but it won't migrate any outdated stuff to the new folder.
|
| |
|
218 |
| The computer's standard startup process takes noticeably longer after upgrading to any Mac OS 9.x system from Mac OS 8.6 or earlier. | May-12-09 |
| |
