| ID | | Article Title | Post Date |
|
27 | 
| How can I distinguish between the earlier Tempo-X eSATA (4+4 and 8e) products supporting 3 Gigabit/sec speeds and the older cards that support 1.5 Gigabit/sec speeds? | May-07-09 |
|
36 |
| What are the benefits of supporting Spread Spectrum Clocking (SSC)? | Mar-02-10 |
|
37 |
| Is it possible to boot from a volume that resides on the Tempo SATA card? | Mar-02-10 |
|
39 |
| Can I hot-swap a disk drive that is attached to any Sonnet Tempo Serial ATA card? | Mar-23-10 |
|
42 |
| Can the Tempo SATA cards co-exist with other manufacturers' Serial ATA cards? | Oct-27-09 |
|
44 | 
| How can I distinguish between the earlier Tempo-X eSATA products supporting 3 Gigabit speeds and the older cards that supported 1.5 Gb speeds? | May-07-09 |
| The new 3 Gigabit/second eSATA cards contain a rather large Marvell chip with the string "88SX6081" on it. Previous generation eSATA cards had a Marvell chip labeled "88SX5081". Additionally, you can check your Macintosh System Profile. When you select the installed eSATA card, the Device ID will show either "0x6081" or "0x5081". |
| |
|
63 |
| Can I operate two Tempo SATA cards in the same system? | Sep-02-09 |
|
67 |
| What kind of performance can I expect from a using a Sonnet Tempo SATA Card in a PCI slot (like in a Power Mac G4)? | Oct-12-09 |
|
174 |
| Drive(s) connected to the Tempo-X SATA 4+4 occasionally do not appear when the computer is booted or an error message regarding the RAID array connected to the Tempo-X SATA 4+4 is occasionally displayed at boot up, and the RAID array cannot be used. | May-07-09 |
|
219 |
| With a Tempo-X SATA host controller installed and drives connected, the computer locks up and will not respond to keyboard or mouse input, and must be forced to power off (press and hold the power button for more than 5 seconds) then restarted. | May-07-09 |
| This condition occurs when the System Preferences Energy Saver Put the hard disk(s) to sleep when possible checkbox is checked (on), or the Disk Sleep Timer is enabled; the Tempo-X SATA card using firmware version 1.2 does not support disk sleep.
To correct this issue, update the Tempo-X card's firmware to version 2.0 or later. Download and run the installer to add disk sleep support. |
| |
|
220 |
| Multiple Hitachi hard drives connected to a Tempo-X SATA host controller are not always detected (won't mount). | May-07-09 |
|
404 |
| The Sonnet Tempo SATA card does not work with my Western Digital My Book Premium ES Edition, or Seagate Technology FreeAgent Pro. | Mar-02-10 |
|
452 |
| I upgraded my Tempo SATA software in a PowerMac G4 or G5 and the card is giving a lot of system errors. | Oct-12-09 |
|
454 |
| I have connected a large hardware RAID volume (for example, a 4TB Fusion D400QR5) to a Sonnet Pro SATA card in a Macintosh, and it is showing up as only 2TB. Why? | Oct-14-09 |
|
459 |
| The performance of my drive array is significantly less than I expect. | Jun-14-11 |
|
544 |
| How do I uninstall the Sonnet Pro SATA Driver? | Dec-26-10 |
| |
