| ID | | Article Title | Post Date |
|
756 | 
| Do the Sonnet USB 2.0 or USB 3 cards support the Apple SuperDrive? | Apr-02-22 |
|
759 |
| My bus-powered USB 3 drive or SSD will not reliably mount or transfer data. | Dec-14-19 |
|
817 |
| Storage connected to a USB 3 PCIe card (or Tango combo card) gives an macOS error message upon wake from sleep. | May-12-20 |
|
933 | 
| What versions of macOS support Allegro USB 3 cards? | Apr-02-22 |
| All Sonnet Allegro (and Fusion Dual 2.5" SSD RAID) PCIe Cards use a macOS pre-installed driver.
These cards are compatible with macOS 10.10 in the MacPro 3,1; 4,1 & 5,1 and in Thunderbolt 2 Expansion chassis.
These cards are not compatible with macOS 10.11, due to a bug in the Apple driver.
These cards are compatible with macOS 10.12 (2)-10.14 in the MacPro 5,1 and in Thunderbolt 2 & 3 Expansion chassis.
These cards are compatible with macOS 10.15-macOS 12 in the 2019 Mac Pro and in Thunderbolt 2 & 3 Expansion chassis.
-------------------------------------------------------------------------------------------------------------------------
Notes:
- These cards are not compatible with Thunderbolt 1 expansion chassis.
- macOS 10.12 erroneously reports a 5Gbps connection when connected at 10Gbps.
- The maximum Apple-supported OS for the Mac Pro 3,1 and 4,1 is OS X 10.11. Dosdude1 offers patchers to allow installation of newer versions of macOS. The Apple USB 3 driver in these patched newer versions will support the Allegro cards.
- Performance of the Allegro cards may be limited by the Mac Pro 5,1 PCIe 2.0 bandwidth.
|
| |
|
956 |
| What generations of Thunderbolt chassis do Sonnet Allegro PCIe cards support? | Apr-02-22 |
| These cards are compatible with only Thunderbolt 2 or 3 PCIe expansion chassis; they are not compatible with Thunderbolt 1 PCIe expansion chassis (unless they have been upgraded to Thunderbolt 2). |
| |
|
971 |
| One or more of my ports has stopped working on my USB 3 card. | Aug-24-22 |
|
1080 |
| What is the difference between USB 3.0, 3.1 and 3.2? | Apr-02-22 |
|
1099 |
| What makes Sonnet USB 3.2 Cards more reliable than other USB 3 cards? | Apr-02-22 |
|
1144 |
| Why does Sonnet use only PCIe 2 to connect the two controllers on these 4-port USB 3.2 Gen 2 cards? | Apr-18-21 |
| We connect each USB 3 controller with two lanes of PCIe 2. Each controller has 1000MB/s bandwidth which is enough bandwidth for the fastest devices you can connect, such as USB 3.1 Gen 2 NVMe SSDs. Because the read/write bandwidth is independent, on one controller you can be reading from one SSD at 1000MB/s, and writing to another at 1000MB/s, plus the same on the 2nd controller for an aggregate transfer rate of 4000MB/s. What makes this possible is that Sonnet uses the advanced ASMedia 3142 Controller that supports Multiple INs, which means that reads can commence on one port before a write has competed on the other port.
A PCIe 3 Bridge chip would cost you $50 more, but would give you incremental performance only if you needed to continually simultaneously read--or simultaneously write--to four USB 3.1 Gen 2 NVMe devices, a very unusual use case.
|
| |
|
1149 |
| How to configure Linux to use Allegro Pro USB card models USB3C-4PM-E and USB3-PRO-4P10-E | May-04-21 |
|
1168 |
| If I put a usb 2.0 and 3.0 device on the same controller will the speeds for the 3.0 device drop to 2.0 like older split-port controllers? | Dec-07-21 |
| |
