| ID | | Article Title | Post Date |
|
756 | 
| Do the Sonnet USB 2.0 or USB 3 cards support the Apple SuperDrive? | Apr-02-22 |
|
759 |
| My bus-powered USB 3 drive or SSD will not reliably mount or transfer data. | Dec-14-19 |
|
817 | 
| Storage connected to a USB 3 PCIe card (or Tango combo card) gives an macOS error message upon wake from sleep. | May-12-20 |
| To minimize power usage during sleep, power is removed from PCIe cards. Because of this power-saving specification, a USB 3 PCIe card is unable to maintain USB port power during sleep. In macOS, this result in a storage device disconnect upon wake from sleep. The storage device will automatically remount, but the system reports a disconnect message. Because macOS flushes all caches before sleeping, this disconnect should never result in any loss of data. |
| |
|
933 |
| What versions of macOS support Allegro USB 3 cards? | Apr-02-22 |
| All Sonnet Allegro (and Fusion Dual 2.5" SSD RAID) PCIe Cards use a macOS pre-installed driver.
These cards are compatible with macOS 10.10 in the MacPro 3,1; 4,1 & 5,1 and in Thunderbolt 2 Expansion chassis.
These cards are not compatible with macOS 10.11, due to a bug in the Apple driver.
These cards are compatible with macOS 10.12 (2)-10.14 in the MacPro 5,1 and in Thunderbolt 2 & 3 Expansion chassis.
These cards are compatible with macOS 10.15-macOS 12 in the 2019 Mac Pro and in Thunderbolt 2 & 3 Expansion chassis.
-------------------------------------------------------------------------------------------------------------------------
Notes:
- These cards are not compatible with Thunderbolt 1 expansion chassis.
- macOS 10.12 erroneously reports a 5Gbps connection when connected at 10Gbps.
- The maximum Apple-supported OS for the Mac Pro 3,1 and 4,1 is OS X 10.11. Dosdude1 offers patchers to allow installation of newer versions of macOS. The Apple USB 3 driver in these patched newer versions will support the Allegro cards.
- Performance of the Allegro cards may be limited by the Mac Pro 5,1 PCIe 2.0 bandwidth.
|
| |
|
956 |
| What generations of Thunderbolt chassis do Sonnet Allegro PCIe cards support? | Apr-02-22 |
|
971 |
| One or more of my ports has stopped working on my USB 3 card. | Aug-24-22 |
| All current and recent Sonnet USB 3 cards have resettable fuses to protect the ports from an overcurrent condition. To reset the fuses, you must remove power to the card by shutting down your machine. (Restarting is not sufficient.) After turning the computer back on, the ports should start working again. If the fuses continue to trip, then you may have a device that draws too much USB Bus power (more than 2 Amps). |
| |
|
1080 |
| What is the difference between USB 3.0, 3.1 and 3.2? | Apr-02-22 |
|
1099 |
| What makes Sonnet USB 3.2 Cards more reliable than other USB 3 cards? | Apr-02-22 |
|
1144 |
| Why does Sonnet use only PCIe 2 to connect the two controllers on these 4-port USB 3.2 Gen 2 cards? | Apr-18-21 |
|
1149 |
| How to configure Linux to use Allegro Pro USB card models USB3C-4PM-E and USB3-PRO-4P10-E | May-04-21 |
| In some computers, USB 3 devices connected to Allegro Pro USB 3 card models USB3C-4PM-E and USB3-PRO-4P10-E are not detected by Linux.
You can fix this by adding the Linux kernel parameter pci=disable_acs_redir=pci:12D8:2308 to the computer's Linux boot script. (Describing how to add a Linux kernel parameter to the computer's Linux boot script is beyond the scope of this FAQ.)
This parameter sets disable_acs_redir for PCIe devices with id 12D8:2308 (which is the PCIe bridge chip on these cards). This parameter disables PCI Express Access Control Services (ACS) functions ACS P2P Request Redirect and ACS P2P Completion Redirect. This has no effect on operation unless you are in a virtualized environment, in which case you must assign all four USB 3 ports to a single virtual machine. |
| |
|
1168 |
| If I put a usb 2.0 and 3.0 device on the same controller will the speeds for the 3.0 device drop to 2.0 like older split-port controllers? | Dec-07-21 |
| |
